Tin Knocker

  • Water Cooled
  • Foot Operated
  • Universal reversible double end ars, 90 & 22 degrees
  • 1" quick release tip holders w/ No. 2 Tape Sockets

  • 24 Gauge Mild Steel Capacity
  • 1/2 HP, 1700 RPM Motor, 115V, 1Phase 
  • 3/16" Flange Height
  • Approx. 35 FPM Speed

  • 20 Ga. Capacity
  • 24" throat slitter
  • 90 FPM 
  • Quick adjusting back gauge and scale

  • Capacity: 22-28 Ga
  • Motor: 5 H.P. motor 230/3/60
  • Speed: 90 FPM
  • Dimensions: 69 x 29 x 49 in

  • 72"  Wide
  • 16 Gauge Capacity w/ Lower Tooling Flanges
  • 16 Gauge Capacity without Lower Tooling Flanges
  • 1" Minimum Flange Width

  • 22 Gauge Mild Steel Capacity
  • 30" Material Width
  • 1HP Motor
  • 110 Volt

  • Weight: 35 lbs
  • Dimensions: 26 x 16 x 12 in
  • Capacity: 20 Ga x 7/32″
  • Minimum Radius: 1 3/4″
$610.00

  • Dimensions: 40″L x 24″W x 44″H
  • Motor: 1 HP, 115/230 Volt, 1800 RPM
  • Capacity: 20-26 Gauge Mild Steel
  • Depth of Pocket: 5/16″ (7.9mm)

  • Manual Front Operated Back Gauge
  • Pull Out Front Sheet Supports
  • Front Dumping Rear Sheet Supports
  • Reversible 4ft Squaring Arm with Embedded Scale and 3 Drops Stops

  • 20 Ga Mild Steel
  • 30" Bend Length
  • .500" Cleat Depth
  • Heavy cast iron and steel fabrication
$875.00

  • Weight: 35 lbs
  • Dimensions: 26 x 16 x 12 in
  • Capacity: 24 Ga Mild Steel
  • UPS: UPS Capable
$665.00

  • Capacity: T-D-P 18-24 ga
  • Forming Sections: 14
  • Shaft Diameter: 1.25″
  • Forming Speed: 50fpm

  • 16 Ga. Mild Steel x 60"
  • 1HP, 115V 1PH
  • Beads are adjustable in depth to 3/16" deep
  • Includes 5 sets of bead tooling

  • Maximum shearing capacity, mild steel: 16 ga. / 1,6 mm
  • Maximum cutting length: 52 in. / 1320 mm
  • Back gauge range: 30 in. / 762 mm
  • Floor space, gauges in position: 66 x 76 x 42 in/ 1676 x 1930 x 1070 mm

  • Capacity: 16-20 Ga. uses approx. 1-3/8” of material
  • Motor: 3HP, 230/3/60, 1PH Optional
  • Depth of pocket size: ½” width of hammer-over edge adjustable up to 3/8
  • Speed: 40-45 ft per minute

  • 20 Gauge Mild Steel
  • 48" x 48" x 46"
  • 190 Lbs.
  • Approx. Footprint 25" x 22" x 42"

  • Dimensions: 41 x 25 x 30 in
  • Speed: Approx. 35 FPM
  • Weight: 305 lbs
  • lange Height: 3/16″

  • Throat to Frame Depth: 13”
  • Throat to Gauge Depth: 12.25”
  • Distance Between Shaft Centers: 3”
  • Motor 1 hp, 230V, 3 phase

 


  • A perfect partner for the TK 16-gauge Pittsburg Roll Former
  • Puts a 3/8″ outside flange on straight or curved sheet metal edges
  • Puts a flange on material with a diameter of as little as 2″
  • Motor: 0.75 HP, 110V, Single Phase

  • 16 Ga. Capacity
  • 48" Bend Length
  • 4" Box Depth
  • Finger Width: 2", 3", 4"

  • Tin Knocker
  • 20 Gauge and Lighter Capacity
  • 25" x 25" x 41"
  • 207 Lbs.

  • Capacity: 22 Ga
  • Forming Length: 36″
  • Roll Diameter: 2″
  • Wire Grooves: Yes

  • Max Capacity 14ga Mild Steel
  • Max Capacity 18ga Stainless Steel
  • 12” Height (Less Handle)
  • 23 lbs.
$465.00

  • Capacity: 24-30 Gauge 
  • Speed:  30ft./minute
  • Uses either 3″ or 6″ width blanks 
  • 3″ to 14″ in diameter out of 24 to 30 gauge galvanized