TPI Corporation 15kW 208V Three Phase Hazardous Location Unit Heater HLA2020836015.024

Features

• 4 FAN-FORCED SUSPENDED UNIT HEATERS 3-25 KW FOR T-3B CLASS I, GROUP C & D, DIVISION 1 & 2 AND CLASS II, GROUPS E, F & G, DIVISIONS 1 & 2.
• Designed for rugged industrial applications in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flammable gases, vapors, powdered metals, or dust
• Permanently sealed, liquid to air, finned tube heat exchanger core
• Ethylene Glycol to water mixture used as a heat transfer fluid in the heater core, providing -45° C. (-49° F) freeze damage protection
• High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution
• Manual Reset capillary type limit provides high temperature regulation and is rated for 6,000 cycles of service
• Stainless steel and aluminum pressure relief valve for overpressure
• A back-up contactor is included for additional protection
• 14 gauge steel cabinet powder coated epoxy paint finish contains heater core, motor, and fan assembly
• Narrow gap safety fan guard shields all moving parts
• Adjustable louvers allow directional control of air
• Copper conductor wires enclosed in rigid metal conduits carry all electrical power
• Box lugs furnished for field connections within approved enclosure
• Made in U.S.A.
• Heat Exchanger and Elements
  • Heavy walled, painted carbon steel with aluminum fins liquid heat exchanger, liquid filled with three-immersion type copper sheathed elements. The elements shall have the highest quality nickel-chromium resistance wire encased in a magnesium oxide dielectric and be hermetically sealed into the heat exchanger core. The heat transfer fluid is Ethylene-glycol solution for operation to -49 degrees F (– 45 degrees C). Stainless steel and aluminum pressure relief valve for overpressure.
• Thermal Cutout High Limit Protection and Optional Pilot Light
  • The capillary type manual reset thermal cutout shall be rated for 6000 cycles of service and mounted in the liquid filled heat exchanger. An optional pilot light to indicate power on, is located on control enclosure.
• Motor
  • The motor shall be a permanent split capacitor type, permanently lubricated, ball bearing type. The motor shall be rated for hazardous location and operate at rated voltage of heater, 60 Hz, 1725 RPM.
• Control Enclosure
  • All controls shall be factory installed and wired in a hazardous location enclosure. Contactors and back-up contactors are heavy duty type and break all ungrounded conductors and be rated for 100,000 cycles at full load. Standard 24-Volt control circuit shall be supplied by internal class II transformer. An optional factory wired integral thermostat or standard terminal block for field wiring to optional remote wall thermostat are wired in control panel. No fan delay relay.
• Disconnect Switch
  • Factory mounted and wired hazardous location disconnect switch is available as optional accessory.
• Cabinet With Adjustable Louvers
  • The Cabinet shall be 14 gauge, cold rolled steel with powder coated epoxy finish. Plated fan guards with less than 1/4 inch spacing to cover motor and fan shall conform to OSHA Requirements.

Specifications

• Catalog Number: 07342002
• Model Number: HLA 20-208360-15.0-24
• Agency Rating: ETL-CUS
• Air Throw: 43
• Amp: 43.5 A
• BTU: 51200
• CFM: 2450
• Control Voltage: 24 V
• KW: 15 kW
• Recommended Mounting Height: 13 ft
• Phase: 3
• Temperature Rise: 19.2
• Voltage: 208 V
• Weight: 193 lbs.
• Dimensions (L x W x H): 30.4” x 22.5” x 24.75”

Options

• Control transformer w/ primary fusing
• 208/240V Control available on 208/240V units
• Disconnect Switch
• Pilot Light
• In-Built single pole thermostat 50° - 90° F
• Mounting Bracket Kits