| Manufacturer Part: | EMT ID: |
|
FS 30C X
|
10683
|
- XYLENT Cutterhead Standard
- Maximum Jointing Width: 12”
- Maximum Working Thickness: 9”
- Motor: 230v / 1ph
XYLENT 12” Cutterhead
Your Minimax FS 30C X includes robust features. From the heavy duty 12” jointer to cast-iron tables and the breakthrough “XYLENT” cutterblock technology, this cutterhead eliminates the necessity of balancing single knives. With the addition of the XYLENT cutterblock, you have long-lasting carbide knives that are designed to last.
Quick Changeover
Changing between jointer and planer is a lot quicker on this machine than other models. Because there are separate dust collection outlets for the jointer and the planer, you do not need to drop the planer table all the way down in order to change back to a jointer. Also, when going back to using the planer function, you don’t have as much distance to travel to get to your planning thickness.
Standard Equipment
- 4.8hp Single phase (230v) motor
- Precision ground cast iron tables
- 3 rows of quarter turn (15x15x2.5mm) knives for Xylent cutterhead
- XYLENT maintenance kit
- American style jointer guard
- Quick tilting jointer fence
- Jointer tables open away from operator
- Two independent dust collection ports
- Tool set & owner’s manual
Specifications
Jointer
- Overall Table Length: 59.75”
- Maximum Jointing Width: 12”
- Cutter Head Speed: 5,200 rpm
- Fence Dimensions: 6” x 51”
- Fence Tilt: 0°- 45°
Planer
- Table Size: 12” x 22”
- Maximum Working Thickness: 9”
- Minimum Working Thickness: 1/8”
- Maximum Stock Removal: 1/8”
- Feed Speed: 23 fpm
Electrical
- Motor: 230v / 1ph
- Overall Dimensions: 32” x 28” x 59”
- Base Dimensions: 26” x 19”
- Weight: 595 lbs
- Dust Collection Outlet Diameter: 4.75”
- Minimum Recommended Dust Extraction Volume: 600 cfm
| Manufacturer | |
| SKU |
FS 30C X
|
| Shipping Method |
LTL Freight
|
| Weight |
625 lb
|
| Dimensions |
48 × 48 × 65 in
|
| Country of Origin |
Italy
|
This is our first experience with a jointer/planer so your mileage may vary.
TLDR: I recommend you buy a more expensive model with a rubber feed roller on the planer (if you can afford it) but good machine for the price. If you decide to buy, read below for some tips on this model.
First off, we sold a Woodmaster to buy this. We were only using the Woodmaster to plane boards so not a direct comparison. However, if I had to do it over again, I would buy a jointer right away and skip the Woodmaster. We need to straighten every board we buy so a jointer is the right tool for the job.
The Tersa system is worth it. We did have a problem with the blades getting bent. This was due to planing a very thin board with a knot in it. The board exploded and bent the blades. We didn't realize the problem for several hours of looking because having a Tersa means you don't need to adjust the blades. Eventually we figured it out and bought new blades. Shame on us, once we got the new blades we bent the old ones straight and now they're fine. Hopefully knowing this will save you a lot of time.
This model has a steel feed roller with teeth. If a piece of wood gets stuck while planing, the feed roller puts a scallop in the top side of the board. Use turtle wax about once a day to keep the wood from getting stuck while feeding. In our experience that eliminates the stuck boards completely.
This machine does not snipe every board but it does snipe most boards. You need to cut your pieces about four and a half inches long, or even better, plane full boards and then cut to length. In the beginning, this seemed like a huge deal because we were cutting and then planing. Once we switched to planing first, now it's not an issue. We've since found out that this is how virtually every pro does it, so again, take our experience with a grain of salt.
After about three months of research, I can tell you that, knowing what I know now, I would have bought a more expensive model with a rubber feed roller on the planer. I believe a rubber feed roller would reduce or eliminate snipe and allow us to feed more than one board at a time. That would have been worth it for our process. However, at this time, it isn't worth upgrading because it's a fine machine.
