Marvel Amada 5 HP 208V Three Phase Vertical Tilt-Frame Band Saw 8-Mark-II VT4555

FREE SHIPPING

Manufacturer Part: EMT ID:
VT4555 (208V)
13124

  • Cast Iron Construction
  • Large Adaptable Work Table
  • Capacity at 90°: 18" x 22"
  • Capacity at 45°: 18" x 12.75"
Details below

Features

  • Controls - IEC fused disconnect switch and magnetic motor starters, with overload and low-voltage protection. Disconnect is NFPA79 compliant. DC Power supply provides low voltage control (24 Volts) to all push buttons at operator’s control panel and machine lighting circuits. PLC control and components mounted in moisture proof NEMA 12 compartment.  Electrical Panel is UL labeled.
  • Mitered Cutting - Column and blade tilt right and left of vertical; work always stationary. Manual tilt standard with Sure-Lock and Built-in protractor.  Electric Power tilt optional.
  • Coolant System - Built In with flood system, available with added optional drop lubrication system (Option Codes ML1 & ML2). Controlled by on-off selector switch at operator’s station. Tank capacity 21 gallons (79 liters).

Specifications

  • Capacity at 90°: 18" x 22"
  • Capacity at 45°: 18" x 12.75"
  • Speed Range 50: 450 fpm (15 – 137 m/min) infinitely variable speed drive system.
  • Front-Mounted Speed Control: Allows blade speed to be adjusted from operator’s control station.
  • Feed Range:  0 – 140 lbs. (64 kgf) infinitely variable direct reading scale balance beam.
  • T-Slotted Work Table Work area: 24.25” x 33” (616 mm x 838 mm); table height 34.5” (876 mm); four machined T-slots accept .625” (15.5 mm) T-Bolts.
  • Miter Cutting: Column and blade tilt up to 45° right and left of vertical; work always stationary. Built-in protractor.
  • Quick-Action Vise: Maximum opening 18” (457 mm). Jaws can be shifted to either right or left side of blade. Jaws are 6” (152 mm) high, 12” (305 mm) wide.
  • Saw Feed Stops: Adjustable stops can be pre-set to stop advance of the saw head and return of blade and to stop motor at any location within the 18” (457 mm) travel of the blade.
  • Coolant System: Built in with Flood system, available with added optional drop lubrication system. (Requires compressed air connection - Option Code ML2). Controlled by on-off selector switch at operator’s station. Tank capacity 21 gallons (79 liters).
  • Flushing Hose: Washes chips from hard-to-get-at places reducing clean-up time.
  • Power Chip Brush: Together with blade wipers and flood coolant keep blade teeth free of chips.
  • Carbide Guide System: Guides are stationary and can be rotated to present new guiding surface to the blade. Upper and lower guides have preloaded carbide-faced back-up blocks to support back edge of the blade.
  • Blade:  14” 6 (4420 mm) long x 1” (25 mm) wide, .035” (89 mm) thick. One Welded-Edge Band Blade is
  • furnished with each machine.
  • Motors: Main; 5 H.P. (3.75 kW), 1800 RPM, totally enclosed fan cooled. Coolant Pump; 1/8 H.P. (.1 kW) totally enclosed motor-built-in integrally.
  • Voltage: 208-volt, 3-phase.
  • Controls: IEC fused disconnect switch and magnetic motor starters, with overload and low voltage protection. Disconnect is NFPA79 compliant. Transformer provides low voltage control (120 Volts) to all push buttons at operator’s control panel and machine lighting circuits. Electrical and control components mounted in a NEMA 12 compartment. Electrical Panel is UL labeled #E56388.

Options

  • 575-3-60 VOLT OPTION: If ordering the 575 volt machine, it will be wired for 480 volt operation and a transformer will be provided with the machine.
  • 220-1-60 VOLT OPTION: A Phase-A-Matic phase converter is shipped with the machine and a 40 AMP service is required.
  • HIGH COLUMN: Column 6” longer than standard, providing increased vertical capacity to 28” at vertical position and 17” high at 45°.
  • HIGH JAWS - JAWS ONLY: 10” high x 12” wide in place of standard jaws provided with machine. Do not permit miter cutting.
  • 45° HIGH JAWS - JAWS ONLY: In place of standard jaws provided with machine. One Front Jaw and one Rear Jaw, both mitered 45°, 10” high x 12” wide.
  • 3° CANTED COLUMN (STANDARD COLUMN): Modification of standard column to add 3° forward approach angle, for increased efficiency in cutting of structural materials. Note: Changes horizontal capacity to 17”.
  • 3° CANTED COLUMN (HIGH COLUMN): Modification of standard High Column to add 3° forward approach angle. Note: Changes horizontal capacity to 16.75”.
  • OPTIONAL HIGH-SPEED MODIFICATION: 120 – 1080 fpm (36 – 329 m/min); main motor changed to 10 H.P., totally enclosed, fan cooled. Only available in 460-3-60 volt machine order.
  • MIST LUBE – AUTOMATIC: Drop Lubrication System. (Requires compressed air connection 60-120psi) SUPPLEMENTARY EQUIPMENT UPON REQUEST.
Manufacturer
SKU
VT4555 (208V)
Shipping Method
LTL Freight
Weight
2,700 lb
Dimensions
101 × 53 × 89 in
Country of Origin
United States of America
Warranty
1 Year
(Parts)
There are currently no reviews for this product.
Be the first to review this product.
Looking for parts? Let us know what you need in the form, or give us a call at 281-241-9504
Marvel Amada 5 HP 208V Three Phase Vertical Tilt-Frame Band Saw 8-Mark-II VT4555
  • Marvel Amada 5 HP 208V Three Phase Vertical Tilt-Frame Band Saw 8-Mark-II VT4555 at Elite Metal Tools
Request Sale Price

This product might qualify for a promotional price. Fill this out and we'll get a quote out to you right away!

Request Financing?

What is the Elite Advantage?

Free Shipping at Elite Metal Tools

Free Shipping

The Elite Metal Tools Promise!
Price Matching at Elite Metal Tools

Price Matching

The best prices on the web.
Customer Service at Elite Metal Tools

Customer Service

Our customers matter.
Knowledgeable Staff at Elite Metal Tools

Knowledgeable Staff

In our business, information is king.
Product Selection at Elite Metal Tools

Product Selection

Your one-stop-shop.