JET

  • Ball bearing support of the motor shaft ensures proper loading, support, and alignment for quiet, accurate operation at any speed
  • Heat treated and polished lead screws are supported by thrust bearings ensuring smooth, incremental movements of the table under load
  • Seamless, one-piece, steel quill is induction hardened and chromed for increased strength and precision ground for greater accuracy
  • Stainless steel Y-Axis way cover provides extra years of protection over the standard sheet metal cover
  • The mounted control box houses major mill functions as well as an emergency stop button
MSRP: $38,932
$31,689
As low as $627.12/mo

  • Ball bearing support of the motor shaft ensures proper loading, support, and alignment for quiet, accurate operation at any speed
  • Heat treated and polished lead screws are supported by thrust bearings ensuring smooth, incremental movements of the table under load
  • Seamless, one-piece, steel quill is induction hardened and chromed for increased strength and precision ground for greater accuracy
  • Stainless steel Y-Axis way cover provides extra years of protection over the standard sheet metal cover
  • The mounted control box houses major mill functions as well as an emergency stop button
MSRP: $39,534
$32,179
As low as $636.82/mo

  • Double end TiN coated mill set
  • Excellent for general-purpose use as TiN provides higher lubricity for freer chip flow, reduced build-up edge formations, and catering
  • Square end mill type to be used for general milling applications
  • TiN (Titanium Nitride) coating provides extreme hardness and heat resistance allowing tool to run at higher speeds and feeds
  • 3/16" to 3/4" by 16ths
MSRP: $301.60
$275

  • Adjustable stops allow automatic shut off
  • Built-in clutch helps prevent damage in overload
  • Includes rapid traverse button
  • Factory installation is available
MSRP: $1,173.71
$965
As low as $31.36/mo

  • Air and coolant line connections are encased in braided metal wire.
  • One gallon tank is made of enamel paint finished metal with removable corrosion resistant inner liner.
  • Flood coolant system for 230/460V 3 Ph machines
MSRP: $626.43
$570
As low as $18.52/mo

  • Adjustable gibs throughout
  • Heavy duty splined motor drive
  • Internal coolant tank built into casting base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
MSRP: $24,724.29
$19,899
As low as $393.80/mo

  • Adjustable gibs throughout
  • Dual locks on all moveable surfaces
  • Heavy-duty spindle brake
  • Precision bored and honed milling head
  • Precision hardened and ground ways and table
MSRP: $34,521.43
$28,099
As low as $556.07/mo

  • 24 volt push button controller with cable strain relief system for durability and reliability
  • All steel construction
  • NEMA 4X compliant push button control pendants
  • Durable powder coat finish
  • Grade 80 Load Chain- Grade 80 black oxide coated load chain for durability
MSRP: $4,460
$2,844
As low as $92.43/mo

  • The 2 in 1 design of the Mechanical Brake and Overload Protection ensure operator safety and extended product life
  • Patented gear limit switch ensures the product switches off power instantly in the case of over lifting or lowering position
  • DC Motor Brake actuates instantly in the event of a power failure to ensure operator safety
  • Two Speed Motor ensures the correct speed for the job with a click of a button
  • IP55 TEFC Motor with Class F insulation for working in harsh environments
MSRP: $12,732
$7,985
As low as $259.51/mo

  • Ergonomically Designed Grip
  • Grinding wheel not included
  • Lightweight composite handle
  • Precision spiral bevel gears transfer torque and speed to spindle for added durability
  • Rugged, ball-bearing design for durability
MSRP: $482
$328.99

  • 4-Position Carriage Stop
  • Chuck guards are standard equipment on all ELITE lathes for increased safety
  • Front facing chip pan allows easy chip removal from the front of the machine
  • Hardened and ground gears in headstock reduce vibration and deflection
  • Inverter drive system provides infinitely variable spindle speeds
MSRP: $31,143.19
$25,101.18
As low as $496.75/mo

  • Articulating LED work lamp
  • Centrally located controls with jog button
  • Electronic Chuck Key Holder
  • Five position automatic carriage stop increases productivity
  • Full length splash guard and coolant return
MSRP: $48,818.57
$39,729
As low as $786.23/mo

  • Extra large hand chain opening for side chain pulling
  • Sealed housing to provide extra protection against the elements
  • Complies with ANSI/ASME B30.16 and HAST-2 Standards
  • Cast steel safety latches
  • Dual pawl Weston style brake
MSRP: $944
$602
As low as $19.56/mo

  • Adjustable gibs throughout
  • Chrome lead screws on X and Y axis
  • Chrome-plated motor shaft with bearing support at end
  • Hardened and ground square vertical knee ways and cross ways
  • Heavy duty motor drive
MSRP: $21,278.57
$17,159
As low as $339.57/mo

  • Articulating LED work lamp
  • Centrally located controls with jog button
  • Electronic Chuck Key Holder
  • Five position automatic carriage stop increases productivity
  • Full length splash guard and coolant return
MSRP: $53,184.29
$43,589
As low as $862.62/mo

  • Certified Meehanite® castings
  • Heavy duty splined motor drive
  • Internal coolant tank built into base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
MSRP: $19,655.71
$15,999
As low as $316.62/mo

  • Grade 80 black oxide coated load chain for added durability
  • Impact resistant all steel construction for added durability and protection
  • Industrial rated alloy steel hooks rotate 360 degrees for easy rigging and slowly stretch to indicate an overload situation
  • Needle bearings support the load sheave to increase efficiency and promote smooth operation
  • JET’s improved easy free chain design is a two-step, no load, free chaining system. The system permits quicker hoist positioning and take up of slack chain, and is engineered not to free chain under load
MSRP: $1,634
$1,069.98
As low as $34.77/mo

  • Ball bearing support of the motor shaft ensures proper loading, support, and alignment for quiet, accurate operation at any speed
  • Heat treated and polished lead screws are supported by thrust bearings ensuring smooth, incremental movements of the table under load
  • Seamless, one-piece, steel quill is induction hardened and chromed for increased strength and precision ground for greater accuracy
  • Stainless steel Y-Axis way cover provides extra years of protection over the standard sheet metal cover
  • The mounted control box houses major mill functions as well as an emergency stop button
MSRP: $41,376.86
$33,679
As low as $666.50/mo

  • Adjustable gibs throughout
  • Dual locks on all moveable surfaces
  • Heavy-duty spindle brake
  • Precision bored and honed milling head
  • Precision hardened and ground ways and table
MSRP: $25,553.06
$20,799
As low as $411.61/mo

  • Ball bearing support of the motor shaft ensures proper loading, support, and alignment for quiet, accurate operation at any speed
  • Heat treated and polished lead screws are supported by thrust bearings ensuring smooth, incremental movements of the table under load
  • Seamless, one-piece, steel quill is induction hardened and chromed for increased strength and precision ground for greater accuracy
  • Stainless steel Y-Axis way cover provides extra years of protection over the standard sheet metal cover
  • The mounted control box houses major mill functions as well as an emergency stop button
MSRP: $29,422.86
$23,949
As low as $473.95/mo

  • Adjustable gibs throughout
  • Heavy duty splined motor drive
  • Internal coolant tank built into casting base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
MSRP: $21,401.43
$17,369
As low as $343.73/mo

  • 12.1" High resolution display (1024 x 768) with 3D graphics
  • 3-D Contouring, ability to import and run G-code files from CAD/CAM programs
  • Adjustable gibs throughout
  • Automatic Lubrication every 180 minutes with a flow of 3-6cc reduces maintenance
  • Available offline software
MSRP: $63,270.20
$51,499
As low as $1,019.16/mo

  • Compatible with Knaack Model CA-02 Cart Armour
  • Handle includes built-in storage bins for versatility
  • Industrial-duty, resin design that resists dents, chips, scratches and corrosion
  • Quiet, non-marking 5 inch casters for increased maneuverability
  • Rounded edges reduce damage to property and personnel
MSRP: $300
$200

  • Ball bearing support of the motor shaft ensures proper loading, support, and alignment for quiet, accurate operation at any speed
  • Heat treated and polished lead screws are supported by thrust bearings ensuring smooth, incremental movements of the table under load
  • Seamless, one-piece, steel quill is induction hardened and chromed for increased strength and precision ground for greater accuracy
  • Stainless steel Y-Axis way cover provides extra years of protection over the standard sheet metal cover
  • The mounted control box houses major mill functions as well as an emergency stop button
MSRP: $42,654.57
$34,719
As low as $687.08/mo

JET was founded in 1977 and has grown into one of the world's largest companies of its kind. Their company is located in Allen, TX. They are a leader in the metalworking industry with design and construction equipment. They sell machines such as a various list and designs of drill press, power tools, and saws.

If you are interested in drill presses or anything else JET has to offer, please contact us. Here at Elite Metal Tools we strive to provide our customers with low prices and fantastic customer service.