JET

  • Layout
Jet JTM-1050EVS2/230 Mill With Acu-Rite 203 DRO With X and Y-Axis Powerfeeds 690621 at Elite Metal Tools
Jet JTM-1050EVS2/230 Mill With Acu-Rite 203 DRO With X and Y-Axis Powerfeeds 690621
  • Automatic oiler releases 3 to 6 cc/cy of lubrication at adjustable time intervals
  • Class 7 spindle bearings support the spindle for maximum rigidity in heavy cutting applications
  • Dual locks on all moveable surfaces
  • Spindle head is internally cooled extending bearing, belt and motor life
  • Swing away control box houses an e-stop and puts all controls at the operators fingertips
MSRP: $33,785.72
$27,166
As low as $537.61/mo
View Details
Jet 1/8-Ton Electric Chain Hoist 1-Phase 10' Lift | BLVS018-010 104000 at Elite Metal Tools
Jet 1/8-Ton Electric Chain Hoist 1-Phase 10' Lift | BLVS018-010 104000
  • Comes standard with Wireless Controller that can infinitely adjust speed from creep to 4ft/min with speed dial and max of 41ft/min in high speed
  • TAA Approved
  • Single phase 120V plug enables use in all areas and the Permanent Magnet Brushless Motor has the lowest required starting current available at just 10amp.
  • Overload protection using slip clutch system to protect hoist from loads over rated capacities
  • Hoist carries a dust and moisture rating of IP-55 and the wireless transmitter IP-65 which means hoist can stay in the light rain and pendant is dust and water proof.
MSRP: $6,590.09
$3,853
As low as $125.22/mo
View Details
Jet JTM-1050VS2 Mill With ACU-RITE 203 DRO With X-Axis Powerfeed, Power Draw Bar and 8" Riser Block 690235 at Elite Metal Tools
Jet JTM-1050VS2 Mill With ACU-RITE 203 DRO With X-Axis Powerfeed, Power Draw Bar and 8" Riser Block 690235
  • Adjustable gibs throughout
  • Chrome lead screws on X and Y axis
  • Chrome-plated motor shaft with bearing support at end
  • Hardened and ground square vertical knee ways and cross ways
  • Heavy duty motor drive
MSRP: $33,109.99
$26,669
As low as $527.77/mo
View Details
Jet JET — Replacement Inner Filter for IAFS 3000 Air Filtration Systems 415157 at Elite Metal Tools
Jet JET — Replacement Inner Filter for IAFS 3000 Air Filtration Systems 415157
$415
View Details
Jet E-1440VS With ACU-RITE 203 DRO With Collet Closer 892455 at Elite Metal Tools
Jet E-1440VS With ACU-RITE 203 DRO With Collet Closer 892455
  • 4-Position Carriage Stop
  • Chuck guards are standard equipment on all ELITE lathes for increased safety
  • Front facing chip pan allows easy chip removal from the front of the machine
  • Hardened and ground gears in headstock reduce vibration and deflection
  • Inverter drive system provides infinitely variable spindle speeds
MSRP: $38,380.53
$30,542
As low as $604.42/mo
View Details
Jet JTM-949EVS Mill With 3-Axis Newall DP700 DRO (Knee) With X, Y and Z-Axis Powerfeeds 690544 at Elite Metal Tools
Jet JTM-949EVS Mill With 3-Axis Newall DP700 DRO (Knee) With X, Y and Z-Axis Powerfeeds 690544
  • Automatic oiler releases 3 to 6 cc/cy of lubrication every 30 minutes
  • Class 7 spindle bearings support the spindle for maximum rigidity in heavy cutting applications
  • Dual locks on all moveable surfaces
  • Spindle head is internally cooled extending bearing, belt and motor life
  • Swing away control box houses an e-stop and puts all controls at the operators fingertips
MSRP: $35,069.53
$28,109
As low as $556.27/mo
View Details
Jet E-1340VS With ACU-RITE 203 DRO With Taper Attachment and Collet Closer 892406 at Elite Metal Tools
Jet E-1340VS With ACU-RITE 203 DRO With Taper Attachment and Collet Closer 892406
  • 4-Position Carriage Stop
  • Chuck guards are standard equipment on all ELITE lathes for increased safety
  • Front facing chip pan allows easy chip removal from the front of the machine
  • Hardened and ground gears in headstock reduce vibration and deflection
  • Inverter drive system provides infinitely variable spindle speeds
MSRP: $41,488.80
$32,826
As low as $649.62/mo
View Details
Jet JTM-1050EVS2/230 Mill With 3-Axis Newall DP700 DRO (Knee) With X-Axis Powerfeed 690639 at Elite Metal Tools
Jet JTM-1050EVS2/230 Mill With 3-Axis Newall DP700 DRO (Knee) With X-Axis Powerfeed 690639
  • Automatic oiler releases 3 to 6 cc/cy of lubrication at adjustable time intervals
  • Class 7 spindle bearings support the spindle for maximum rigidity in heavy cutting applications
  • Dual locks on all moveable surfaces
  • Spindle head is internally cooled extending bearing, belt and motor life
  • Swing away control box houses an e-stop and puts all controls at the operators fingertips
MSRP: $32,839.72
$26,471
As low as $523.86/mo
View Details
Jet JTM-1 Mill With Newall DP500 DRO 692187 at Elite Metal Tools
Jet JTM-1 Mill With Newall DP500 DRO 692187
  • Heavy duty splined motor drive
  • Internal coolant tank built into base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
  • Precision bored and honed milling head
MSRP: $19,190.26
$14,969
As low as $486.49/mo
View Details
Jet JTM-1050EVS2/230 Mill With 3-Axis Acu-Rite 203 DRO (Quill) With X, Y and Z-Axis Powerfeeds 690633 at Elite Metal Tools
Jet JTM-1050EVS2/230 Mill With 3-Axis Acu-Rite 203 DRO (Quill) With X, Y and Z-Axis Powerfeeds 690633
  • Automatic oiler releases 3 to 6 cc/cy of lubrication at adjustable time intervals
  • Class 7 spindle bearings support the spindle for maximum rigidity in heavy cutting applications
  • Dual locks on all moveable surfaces
  • Spindle head is internally cooled extending bearing, belt and motor life
  • Swing away control box houses an e-stop and puts all controls at the operators fingertips
MSRP: $38,380.53
$30,542
As low as $604.42/mo
View Details
Jet JTM-1254RVS with X & Y Powerfeeds 698086 at Elite Metal Tools
Jet JTM-1254RVS with X & Y Powerfeeds 698086
  • Adjustable gibs throughout
  • Dual locks on all moveable surfaces
  • Heavy-duty spindle brake
  • Precision bored and honed milling head
  • Precision hardened and ground ways and table
MSRP: $31,488.26
$25,399
As low as $502.64/mo
View Details
Jet JTM-4VS Mill With ACU-RITE 203 DRO With X and Y-Axis Powerfeeds and Power Draw Bar 690230 at Elite Metal Tools
Jet JTM-4VS Mill With ACU-RITE 203 DRO With X and Y-Axis Powerfeeds and Power Draw Bar 690230
  • Adjustable gibs throughout
  • Heavy duty splined motor drive
  • Internal coolant tank built into casting base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
MSRP: $28,379.99
$22,376
As low as $442.82/mo
View Details
Jet JTM-949EVS with Newall DP700 DRO & X Powerfeed 690535 at Elite Metal Tools
Jet JTM-949EVS with Newall DP700 DRO & X Powerfeed 690535
  • Automatic oiler releases 3 to 6 cc/cy of lubrication every 30 minutes
  • Class 7 spindle bearings support the spindle for maximum rigidity in heavy cutting applications
  • Dual locks on all moveable surfaces
  • Spindle head is internally cooled extending bearing, belt and motor life
  • Swing away control box houses an e-stop and puts all controls at the operators fingertips
MSRP: $29,393.53
$23,121
As low as $457.56/mo
View Details
Jet MT100-4, 1- Ton Two Speed Electric Trolley 3-Phase 460V 144185 at Elite Metal Tools
Jet MT100-4, 1- Ton Two Speed Electric Trolley 3-Phase 460V 144185
  • Heavy-Duty motor puts out up to 0.8HP making it the strongest in it's class
  • TAA Approved
  • Two speeds reduce bump firing to while still allowing for high-speed movement of materials
  • Indoor and Outdoor use with IP-55 rating for trolley and IP-65 rating for the pendant
  • Expanded flange capacity kits are available
MSRP: $4,162.39
$2,415
As low as $78.48/mo
View Details
Jet JTM-4VS Mill With 3-Axis ACU-RITE 203 DRO (Quill) 690184 at Elite Metal Tools
Jet JTM-4VS Mill With 3-Axis ACU-RITE 203 DRO (Quill) 690184
  • Adjustable gibs throughout
  • Heavy duty splined motor drive
  • Internal coolant tank built into casting base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
MSRP: $24,325.72
$19,397
As low as $383.86/mo
View Details
Jet JTM-1 Mill With 3-Axis Newall DP700 DRO (Quill) With X and Y-Axis Powerfeeds 691192 at Elite Metal Tools
Jet JTM-1 Mill With 3-Axis Newall DP700 DRO (Quill) With X and Y-Axis Powerfeeds 691192
  • Heavy duty splined motor drive
  • Internal coolant tank built into base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
  • Precision bored and honed milling head
MSRP: $24,866.26
$19,794
As low as $391.72/mo
View Details
Jet JET — JWP208-K Replacement Knives for JWP208 Planers, Set of 4 708808 at Elite Metal Tools
Jet JET — JWP208-K Replacement Knives for JWP208 Planers, Set of 4 708808
  • Compatible with many other brand tools lets you buy these knives with confidence
  • High-speed steel construction means longer cutting life between sharpening
  • Hardened and tempered to 62-64 Rockwell
  • Precision balanced to ensure quality cuts every time
  • Set of 4
MSRP: $324.27
$289
View Details
Jet JTM-1050VS2 Mill With X and Y-Axis Powerfeeds 690150 at Elite Metal Tools
Jet JTM-1050VS2 Mill With X and Y-Axis Powerfeeds 690150
  • Adjustable gibs throughout
  • Chrome lead screws on X and Y axis
  • Chrome-plated motor shaft with bearing support at end
  • Hardened and ground square vertical knee ways and cross ways
  • Heavy duty motor drive
MSRP: $27,028.53
$21,383
As low as $423.16/mo
View Details
Jet ETM-949 Mill with 3-Axis ACU-RITE 203 (Quill) DRO and X-Axis JET Powerfeed and USA Made Air Draw Bar 894118 at Elite Metal Tools
Jet ETM-949 Mill with 3-Axis ACU-RITE 203 (Quill) DRO and X-Axis JET Powerfeed and USA Made Air Draw Bar 894118
  • Ball bearing support of the motor shaft ensures proper loading, support, and alignment for quiet, accurate operation at any speed
  • Heat treated and polished lead screws are supported by thrust bearings ensuring smooth, incremental movements of the table under load
  • Seamless, one-piece, steel quill is induction hardened and chromed for increased strength and precision ground for greater accuracy
  • Stainless steel Y-Axis way cover provides extra years of protection over the standard sheet metal cover
  • The mounted control box houses major mill functions as well as an emergency stop button
MSRP: $41,286.07
$32,677
As low as $646.67/mo
View Details
Jet JTM-1254RVS with NEWALL DP700 DRO X, Y & Z Powerfeeds & Air Power Drawbar 698131 at Elite Metal Tools
Jet JTM-1254RVS with NEWALL DP700 DRO X, Y & Z Powerfeeds & Air Power Drawbar 698131
  • Adjustable gibs throughout
  • Dual locks on all moveable surfaces
  • Heavy-duty spindle brake
  • Precision bored and honed milling head
  • Precision hardened and ground ways and table
MSRP: $40,272.53
$31,932
As low as $631.93/mo
View Details
Jet JTM-1 Mill With 3-Axis Newall DP700 DRO (Quill) 691190 at Elite Metal Tools
Jet JTM-1 Mill With 3-Axis Newall DP700 DRO (Quill) 691190
  • Heavy duty splined motor drive
  • Internal coolant tank built into base for use with coolant system (Coolant pump not included)
  • Large Diameter quill is chromed
  • One shot lubrication system
  • Precision bored and honed milling head
MSRP: $22,433.72
$17,504
As low as $346.40/mo
View Details
Jet ETM-949 Mill with 3-Axis Newall DP700 (Quill) DRO and Servo X, Y-Axis Powerfeeds and USA Air Powered Draw Bar 894226 at Elite Metal Tools
Jet ETM-949 Mill with 3-Axis Newall DP700 (Quill) DRO and Servo X, Y-Axis Powerfeeds and USA Air Powered Draw Bar 894226
  • Ball bearing support of the motor shaft ensures proper loading, support, and alignment for quiet, accurate operation at any speed
  • Heat treated and polished lead screws are supported by thrust bearings ensuring smooth, incremental movements of the table under load
  • Seamless, one-piece, steel quill is induction hardened and chromed for increased strength and precision ground for greater accuracy
  • Stainless steel Y-Axis way cover provides extra years of protection over the standard sheet metal cover
  • The mounted control box houses major mill functions as well as an emergency stop button
MSRP: $45,272.80
$35,606
As low as $704.64/mo
View Details
Jet JTM-1050VS2 Mill With ACU-RITE 203 DRO With X, Y and Z-Axis Powerfeeds and Power Draw Bar 690258 at Elite Metal Tools
Jet JTM-1050VS2 Mill With ACU-RITE 203 DRO With X, Y and Z-Axis Powerfeeds and Power Draw Bar 690258
  • Adjustable gibs throughout
  • Chrome lead screws on X and Y axis
  • Chrome-plated motor shaft with bearing support at end
  • Hardened and ground square vertical knee ways and cross ways
  • Heavy duty motor drive
MSRP: $33,380.26
$26,868
As low as $531.71/mo
View Details
Jet 2-Ton Two Speed Electric Chain Hoist 3-Phase 10' Lift | TS200-460-010 144007 at Elite Metal Tools
Jet 2-Ton Two Speed Electric Chain Hoist 3-Phase 10' Lift | TS200-460-010 144007
  • The 2 in 1 design of the Mechanical Brake and Overload Protection ensure operator safety and extended product life
  • Patented gear limit switch ensures the product switches off power instantly in the case of over lifting or lowering position
  • DC Motor Brake actuates instantly in the event of a power failure to ensure operator safety
  • Two Speed Motor ensures the correct speed for the job with a click of a button
  • IP55 TEFC Motor with Class F insulation for working in harsh environments
MSRP: $13,426.59
$7,633
As low as $248.07/mo
View Details

JET was founded in 1977 and has grown into one of the world's largest companies of its kind. Their company is located in Allen, TX. They are a leader in the metalworking industry with design and construction equipment. They sell machines such as a various list and designs of drill press, power tools, and saws.

If you are interested in drill presses or anything else JET has to offer, please contact us. Here at Elite Metal Tools we strive to provide our customers with low prices and fantastic customer service.