DoALL 10” x 16” Structural Band Saw with Variable Frequency Drive 400S-SA

Features

Fixed Control Console

Ergonomically placed control console for ease of operation and safety of the operator.

Variable Frequency Band Drive

The Variable Frequency Band Drive allows the operator to dial in their band speed to fine tune cutting performance supplying maximum torque to the tooth tips of the saw band.

Rapid Head Down with Feed Control

Three position head control allows the operator in rapid mode to quickly position the saw head above the material, the head will stop at position in the hold mode, and create feed rates with the micrometer adjustment in the feed mode for maximizing cutting performance.

Coolant Thru Carbide Faced Saw Guide Inserts

Supplies coolant to the blade evenly before the cut creating straighter cuts and allowing longer blade life due to coolant being supplied at the tooth tip.

Band Wheels

Flange cast steel wheels insure band tracking to prevent tooth set loss.

Rack and Pawl Vise

Time honored rack and pawl vice system using an acme thread screw minimizes setup / clamping time aiding in increased production and decreased vise maintenance.

Manual Blade Tension

Positive stop to prevent possible error of over/under tightening the band for maximum cutting rates and band life.

Band Brush

Gear driven band brush removes the chips from the blade gullets which would prevent the blade from attaining maximum cutting rates and blade life.

Counter Balance Spring

Counterbalance spring maintains constant head weight thru out the cut keeping the blade tooth load equal aiding in maximum blade life.

Full Cycle Attachment (Included Accessory)

The full cycle attachment provides pneumatic head raise/vise operations allowing for head raise to a pre-determined height after the cut in auto mode. Pneumatic operations remain active in manual mode.

Standard Equipment

• Swivel head to 45 degrees.
• Fine adjustment head feed control.
• Fixed control console
• Rapid head down approach.
• Spring loaded, zero clearance, coolant through, carbide faced saw guide inserts.
• Quick action rack and pawl vise system w/Acme Thread.
• Gear driven band cleaning brushes.
• Variable Frequency Drive
• Heavy duty counterbalance spring.
• Flange backing band wheels.
• Manual band tension.
• Recirculating coolant system.
• Discharge Tray.
• Replaceable steel wear plates on bed.
• Saw blade guards.
• Band door interlocks.
• One (1) complimentary DoALL Bi Metal saw blade.
• Complimentary DoALL Cutting Fluids package.

Specifications

• Cutting Capacity:
  • Capacity at 90° Rectangle: 10” x 16”
  • Capacity at 90° Round: 10-3/4”
  • Capacity at 45° Rectangle: 9” x 10-3/4”
  • Capacity at 45° Round: 10-3/4”
• Saw Blade:
  • Band Width: 1” x 0.035”
  • Band Length: 158”
• Band Drive:
  • Motor HP: 2 HP VFD
  • Band Speed: Variable, 50-400 fpm
  • Band Tension: Manual
• Coolant System:
  • Flood: Yes
  • Mist Lubricator: No, Optional – see accessories
  • Motor HP: 1/15 HP
  • Reservoir Size: 6 Gallons
• Floor Space Dimensions:
  • Material Pass Line Height: 29”
  • Floor Space Required: 87x 42 x 55”
  • Weight: 1200 lbs
• Electrical:
  • Voltage Requirement 208V,230V or 460V-60Hz-3ph, Wye configuration (Must Specify at Order Placement)
  • Total Amp Draw (FLA) 7.2(208)  6.9(230) 3.5(460)Amps

Available Options

• 5 ft Medium-duty idler conveyor 16" between frames. Roller capacity 850 Ibs.
• 10 ft Medium-duty idler conveyor 16" between frames. Roller capacity 850 Ibs.
• Additional conveyor rollers
• 24" Discharge table
• 18" Adjustable work stop - Requires item 1009399
• Band mist lubricator
• Work light
• Laser line generator
• Flushing hose attachment
• Four (4) hours installation and operator training
• DoALL Cut Above 10 Year Warranty Annual Investment