TPI Corporation 2600 Series 15kW 208V Three Phase Downflow Unit Heater F3F2615CA1

Features

• 16 gauge steel cabinet with epoxy powder coated finish and control compartment with a hinged and latched access door.
• OSHA guards standard with all models.
• Made in U.S.A.
• Corrosion resistant element with steel sheath and steel spiral fins.
• All units come equipped with manual reset limit controls to de-energize the heater should an over-temperature situation occur.
• Totally enclosed, 1 speed, 1 phase permanently lubricated, thermally protected motors with unit bearings on 3KW - 20KW models.
• Axial flow fan blade - 1570 RPM max.
• All models equipped with fan purge which allows fan to operate after elements are de-energized to purge residual heat.
• 208V, 240V, 277V and 480V units have In-Built 24 Volt transformer for low voltage remote thermostat application.
• All models equipped with In-Built disconnect except F3F2640, F3F2630CA1, F3F2650, H3H2650, and H3H2640CA1.
• Unit can be mounted using optional mounting bracket or field constructed angle iron bracket.
• Not recommended for mounting with threaded rod or chain.
• SPECIFICATIONS:  The contractor shall furnish and install the 2600 Series electric vertical discharge unit heaters of the size, capacity and voltage specified. Heaters shall be installed according to the manufacturer’s recommendations and applicable national and local codes.
• ELEMENTS: Elements shall consist of Nickel Chromium alloy resistance wire embedded and completely surrounded in Magnesium Oxide, enclosed, and swagged into corrosion resistant sheaths. Corrosion resistant steel fins shall be permanently attached to the sheaths to provide maximum heat transfer to the air stream.
• MOTORS: Motors shall be single phase, resilient mounted, totally enclosed, industrial rated with an automatic reset thermal overload protective device. Motors on heaters up to 20 KW capacity shall be permanently lubricated shaded pole type. Motors shall be mounted out of the main air stream in such a manner as to allow ambient air to be drawn over the motor to reduce motor temperature. Motor shall be separately removable from beneath the heater without removing the entire heater from mounting bracket.
• FAN BLADES: Fan blades shall be heavy-duty individually balanced axial flow type. Fan speed shall not exceed 1570 RPM.
• THERMAL OVERLOAD PROTECTION: All heaters shall be equipped with a manual reset thermal cutout which disconnects elements and motor in the event normal operating temperatures are exceeded.
• WIRING: Heaters shall be designed for a single supply circuit with elements, motor and control circuits subdivided and fused to conform with the latest National Electric Code and OSHA requirements. All three phase heaters shall have balanced phases.
• CONTROLS: Heaters shall be controlled by a low voltage wall mounted thermostat. 5 KW through 20 KW units are single stage. All heaters shall be equipped with a fan safety device that causes fan to operate after elements are de-energized to purge unit of residual heat.

Specifications

• Catalog Number: 07159602
• Model Number: F3F2615CA1
• Amp: 41.68 A
• BTU: 51195
• CFM: 1200
• Control Voltage: 24 V
• KW: 15
• Mounting Height Max.: 20 ft
• Mounting Height Min.: 6 ft
• Agency Rating: ETL-CUS
• Phase: 3
• Temperature Rise: 39
• Voltage: 208 V
• Color: Grey
• Weight: 75 lbs.
• Dimensions (L x W x H): 20.5” x 20.5” x 15”

Options

• L00E-01 – Ceiling Mount Stratification Thermostat - SPDT; 24V, 120-277V; 1/4 HP @ 125 VAC, 1/2 HP @ 240 VAC; 22 Amp Resistive; 50-60 HZ, Pilot Duty 24V 50VA; 70-140°F
• FSW5112 – Summer Fan Switch - SPST; LOW VOLT; (W/RELAY)
• A1600 – Ceiling Mount Bracket 5-20 KW Models
• D1602 – Linear Louvered Diffuser 5-20 KW Models
• D1600 – Radial Louvered Cone Diffuser 5-20 KW Models
• D1603 – Anemostat Diffuser 5-20 KW Models